Accufast Kt Tabber Manual

How do I adjust and clean the Accufast KT Tab Sensor? Published: December 3, 2011 UPDATED If you experience tabbing problems on the Accufast KT, tune the sensor for – Also know as a KT Sensor Reset: WARNING DO NOT PLACE FINGERS OR TOOLS BETWEEN OR NEAR MOVING PARTS. 1) Turn the POWER SWITCH off. 2) Remove any tabs and debris from the peel point area through the INSPECTION WINDOW on the input end, below the threading path. CAUTION IF ALL TABS AND DEBRIS ARE NOT REMOVED FROM THE PEEL POINT AREA BEFORE CLEAR TAB IS ACTIVATED, THE SENSOR’S DEFINITION OF CLEAR TABS WILL CHANGE AND CLEAR TABBING WILL BE PREVENTED. On the product entry side, there is an elongated hole under where the tabs peel off, see below If you look inside the hole, you will see the bottom portion of the sensor.

(The black circle in the white plastic, see photo below) Clean it off with some. Also, make sure no tabs are anywhere in the path. If you remove the tabs and look from the exit side, you can see the top portion of the sensor. In the photo below, look for the rectangle with the nut on it.

The sensor is on the bottom of the white housing directed down at the lower sensor. Once you have this area clean turn the KT back on and, 3) Toggle CLEAR TAB off and wait, a few seconds 4) Toggle CLEAR TAB on.

Go Back to: > > > Accufast KT 1.5 Tabletop Tabbing Machine The ACCUFAST KT 1.5 is a feature rich basic tabbing machine. The KT 1.5 lets you use 1' or 1.5'. Accufast KT Dual Mode Tabber. Accufast KT Dual Mode Operator User Manual 50 pages. Accufast KT Operator User Manual 50 pages. Accufast KT Parts.

5) Toggle ON/OFF until a tab advances to the peel point and the TAB READY light illuminates.Your sensor has now been re-calibrated!Another thing to check is to make sure the tabs are threaded correctly! See photos below. Below Shows to correct way to thread the Accufast KT Tabber Correct Incorrect Do you need a KT?

Give All For Mailers a call at 866-430-2874 New and Used Accufast KT available! Need Need Replacement Parts? SuppliesForMailers.com has them! Need a parts breakdown / parts manual? Try Find the part, click on it and order! Need some help replacing the tab sweep? Check out Similar Posts: • Posted November 28, 2017 • Posted August 30, 2011 • Posted November 27, 2017 • Posted May 19, 2010 • Posted June 4, 2009.

The ACCUFAST ET Tabber automatically tabs both booklets and self-mailers with the appropriate tabs in the correct spots. Simple to Use • Very little setup and operator interaction required • Select the correct Tab Mode • Load the proper tabs • Feed pieces from whatever device you choose on the front end • Clean out the waste when it's full • Splice on another strip of tabs when the first one runs out We've organized this presentation around the two major applications: Booklets and Self Mailers. Booklets The USPS defines a booklet as a folded mailer with a spine and some sort of device (staple or glue) to close the spine. The regulations require at least two and usually three 1 ½” tabs to close the booklet for self-mailing. The specification for the location of the tabs is quite precise. Booklet tabbing is most often an off-line activity. Typically a feeder such as the ACCUFAST FX or ACCUFAST HDF is used in-line with the ET, and the booklets are fed spine first into the tabber.

Tabs are applied based on the tab mode selected at the start of the run. The location of the tabs is automatically set based on the size of the piece being used and USPS specification. Tabs are usually supplied to the ET in high volumes from a box of fan-folded tabs located on the floor below the machine.

This eliminates much of the handling of tabs. Just splice one stack of tabs to the next and run the whole thing, stopping for a few seconds occasionally to clear the waste paper spool. Self-Mailers The self-mailer is pretty much as it always has been except that either top or edge tabbing is allowed. The ACCUFAST ET does both with the twist of a knob. Because a self-mailer often starts out as a single sheet of paper, the ET can easily become part of a mail production system that can include a paper folder, the ET, a transfer table and an ink jet address printer. All of these modules are available from ACCUFAST.

Looking to Increase Efficiency and Deliver Profitability in your operations? OAM can help. To find out more about the ACCUFAST ET Tabber or other products from OAM, simply fill out the form on this page and one of our representatives will be in touch.

For sales and service inquiries and to learn more about our competitive pricing on ink, tabs and supplies, contact us now at 216.391.3000.