Proshivka Carprog 809

Make the Universal tool - CARPROG inside have powerful 16-bit MPU and full set of automotive interface drivers. In basic version you will get hardware with extra functions: 12 input/output pins forEEPROM in-circuit programmer, future possibility's to make on the same hardware Microcontroller programmer, Immobiliser Transponder Key programmer with antenna adapter for 125/134 kHz, K-line diagnostic (dashboard odometer programming, immobilizer key programming), CAN line diagnostic,+5V/+12V output, USB, power supply only from USB.

Apr 29, 2017 - Free shipping ORIGINAL RT809H with 16 ORIGINAL ADAPTERS WITH. Car Repair Tool Carprog V7.28 Programmer For Car Radios.

(, 07:09 AM)Willail Wrote: (, 12:23 PM)dil6222 Wrote: (, 11:15 AM)Willail Wrote: (, 05:00 AM)23Andi23 Wrote: (, 04:51 AM)Willail Wrote: Hello, change the 4 IC 74HC125D is the only modification to rework carprog 7.28? Thanks for your help What not work?

Antenna is working? Can bus is working? Hello, i have a clone carprog using solfware 7.28. Since i received it, it is impossible to read eeproms 95160 and 24cxx. I so used the software with airbag, but the ID of the Eproom is not recognised.

The eprooms were desolder from the pcb and i used the A4 and A5 adapters provided with carprog. I have verified that the wires were correct with a multimeter (continuity test). I don't know if the changes of the 4 IC will help to read eprooms. I very dissapointed I don't test if antenna and CAN bus are working? How do i make it?

Thanks for your reply (, 10:47 AM)23Andi23 Wrote: (, 10:00 AM)Willail Wrote: Hello, Do you have already reworked clone carprog V7.28? Thanks Hello, What's a good pcb of carprog? COuld you send me a picture? Yhanks Look one Page back post nr.

780 in this thread Most people flash to 8.21 and make rework like on many pictures in this thread Hello, thank you for this reply. I will send you some picture of my carprog. Then, you will tell me if it is a good pcb. Can you give the main changes to make at the rear of the pcb because on the pictures, it is not easy to understand (remove some capacitors, remplace by a what?

Repair the hole line missing? Thanks (, 06:27 AM)kastanka Wrote: (, 17:27 PM)dil6222 Wrote: That's 1 of a few mods you can do you can try this but I haven't tested it.

I tested it and work perfect. Hello, could you explain me the changes that you made on your carprog for held reading and writing eprooms? Add a 120 ohm resistor and change the 4 iC 74HC125D by 74HCT125M? Here we go this is good start and yes change 4x 74HC125D to 74HC125M i will post some pictures of the other mods shortly hope this helps don't forget to thanks and rep those who have helped you Hello, thank for your reply.

Do you know where i can buy some good 74HCT125M? It is possible to buy on Ebay? Some friends say that the components on Ebay are not original and are bad. Thanksi not change 4x 74HC125D to 74HC125M and well read-write 24cxx,95x without any problem. (, 09:40 AM)kastanka Wrote: (, 07:09 AM)Willail Wrote: (, 12:23 PM)dil6222 Wrote: (, 11:15 AM)Willail Wrote: (, 05:00 AM)23Andi23 Wrote: What not work? Antenna is working? Can bus is working?

Hello, i have a clone carprog using solfware 7.28. Since i received it, it is impossible to read eeproms 95160 and 24cxx. I so used the software with airbag, but the ID of the Eproom is not recognised. The eprooms were desolder from the pcb and i used the A4 and A5 adapters provided with carprog. Andrej biljzho moya veneciya chitatj onlajn. I have verified that the wires were correct with a multimeter (continuity test). I don't know if the changes of the 4 IC will help to read eprooms. I very dissapointed I don't test if antenna and CAN bus are working?